NEW PRODUCTS

 

Skull Shroud  (3/28/10) For the Ultimate Look For more information and to order - Click here
Performance Bearings  (3/28/10) We now offer Ceramic, ABEC 5/7, C3/C4, & Other bearings See Race Parts more information and to order - Click here
Light Weight Flattop, GX200  (2/28/10) Approx 9 grams lighter than stock piston. Available in T2 (1.6mm rings) or T3 (1.0mm Rings). Fits both GX160 and 200 (6.5) engines This is the Only T3 Piston available to fit GX200s See Race Parts more information and to order - Click here
STARTER NUTS (2/28/10) Extended starter nut for use with handheld starters, Uses 3/4" Socket See Engine Accessories more information and to order - Click here
SOX BSP EXHAUST (2/28/10) These are the best performing exhaust available for the BSP class See Exhaust more information and to order - Click here
307 CAM GRINDS (12/28/09) Six months in development, this grind was specially developed for GX200s. Using a flat top style lobe, this cam has 260 duration. It is a serious camshaft for serious motors and big tracks. Special Ramp Designed for Honda (and Clone) GX200s running 12 to 1 or higher compressions using Race Gas or Methanol. Use with Dual springs and 1.3 rockers. This is the cam for 20+ HP motors See Race Parts more information and to order - Click here
EXHAUST KIT (12/28/09) Cant find a system to fit your application. Use this kit to fabricate your own system. Can be either clamped or welded together. See Exhaust more information and to order - Click here
MANIFOLD FOR 390 CARBS (12/28/09) See Race Parts more information and to order - Click here
SHORT MANIFOLD FOR MIKUNIS AND 390 CARBS (11/17/09) See Race Parts more information and to order - Click here
ALKY CONVERSION KITS (11/17/09) For use with OEM Carbs running Alky See Race Parts more information and to order - Click here
ALKY E-TUBE (11/17/09) For use with OEM Carbs running Alky See Race Parts more information and to order - Click here
MINI BIKE EXHAUST  (11/17/09) New pipe esp for Mini Bikes See Exhaust more information and to order - Click here
TACHS (10/12/09) See Engine Accessories more information and to order - Click here
Valve Cover Spacer (9/17/09) Allows stock valve cover to work with roller rockers. See Race Parts more information and to order - Click here
Steel Roller Rockers (9/17/09) Low cost and super strong alternative to aluminum rollers. See Race Parts more information and to order - Click here
Chrome Plated Valve Cover (9/10/09) See Stock Parts more information and to order - Click here
Clutches (9/10/09) We now offer Clutches See Clutches for more information and to order - Click here
Light Weight Sungear for HX2 Hondas (7/18/09) Light Weight Sungear for Half and Outlaw 1/4 Midgets See Race Parts more information and to order - Click here
Go NoGo Gauges for Honda and Clone Carbs (7/06/09) Go NoGo gauges for checking and teching Honda Carbs. Includes .615 for AKRA Clone Carbs. See Tools for information and to order - Click here
Bugle Pipe for Hondas and Clones (6/04/09) New  Bugle Exhaust Pipe Esp for Honda and Clones. Max length for max power See Exhaust for more information and to order - Click here
Half Midget Pipe (6/04/09) Half Midget Pipe. See Exhaust more information and to order - Click here
Air Filter Adapter for 22 Mikuni Carbs (6/02/09) Allows use of Large Air Filters when using Mikunis See Race Parts more information and to order - Click here
Short Spark Plug for milled heads (5/16/09) NGK Short Plugs These plugs have shorter reach than stock plugs. Needed when using excessively milled heads to prevent piston to spark plug interference. See Race Parts more information and to order - Click here
Low Cost RTT Clone Pipe - Uses Briggs Muffler (5/16/09) New  Exhaust Pipe Esp for Clones and Box Stock Super Classes. Has fitting for screw Briggs (5 hp) Muffler See Exhaust more information and to order - Click here
SCREW IN PULSE FITTING (5/12/09) See Engine Accessories more information and to order - Click here
610 HONDA CARB FOR CLONES (5/11/09) Genuine Honda carb bored and blueprinted to Clone (.610) specs. These carb meet the .610 bore of most Clones classes but outperform the clone carbs. Circuitry is reworked to enhance low end performance See Race Parts more information and to order - Click here
Valve Cover with Pulse Fitting (3/20/09) See Race Parts more information and to order - Click here
MINI BIKE EXHAUST  (3/20/09) New pipe esp for Mini Bikes See Exhaust more information and to order - Click here
VALVE SPRING COMPRESSOR (3/12/09) Valve Spring Compressor for installing valve springs on Honda (and clone) Heads See Tools more information and to order - Click here
LOW COST FUEL PUMP (3/12/09) FUEL PUMP, Mikuni, Pulse Operated, Plastic Housing See Engine Accessories more information and to order - Click here
ROLLER ROCKERS (3/12/09) Roller Rocker Arms,  1.3 Ratio. RaceSeng Design. Use with Stock Height Valves. Set. See Race Parts more information and to order - Click here
FLYWHEEL SCREEN (3/2/09) Fits Hondas and Clones. Reduces Air Flow and protects fan/flywheel. Available in Red, Yellow, Blue, or Black. Now in Aluminum or Plastic See Engine Accessories more information and to order - Click here
Black Clone Pipe (Rapp) (2/26/09) New Black Exhaust Pipe Esp for Clones and Box Stock Super Classes. Use with or without muffler. See Exhaust more information and to order - Click here
Genuine Honda Electric Start Kit (2/26/09) For GX160s and 200s (Fan cover requires minor trimming on 200). Includes all parts needed including charging coil. All parts are Genuine Honda. See Stock Parts more information and to order - Click here
285 CAMSHAFT SERIES (2/12/09) New 280 lift cam with 250 duration. Developed for GX200s using large carbs, high compression, and good flowing heads. More top end power than our 280 series and easier on valve train than 320 series. Capable of 20 hp with correct combination. See Race Parts more information and to order - Click here
PUSH RODS, CHROME MOLY (2/5/09) We Now have push rods that allow use of 160 Lifters with use of 160 Lifters in 200 blocks to reduce valve train weight. Reduces combined lifter/Pushrod weight by approx 7%. See Race Parts more information and to order - Click here
INTAKE MANIFOLD SPACER WITH PULSE FITTING (1/31/09) Aluminum spacer with pulse fitting can be used either in front or behind carb. Run your fuel pump without getting oil in it and/or having to drill into the block. When used behind carb, dyno testing has shown up to 0.2 hp improvement due to longer intake tract. Improvement is over entire RPM range. Even if you don't need a fuel pump, this piece adds power.   See Race Parts more information and to order - Click here
BLUE CLONES (1/31/09) Now available from NR Racing, Blue Clones, Stock or Built See Clone Page for information and to order - Click here
CHAIN GUARDS  (1/31/09) See our selection of chain guards and heat sheilds See Engine Accessories more information and to order - Click here
CHOKE HOLDER  (1/25/09) Our new Choke Holder allows you to retain the factory choke lever when using aftermarket air filter adapters. Most adapters must be drilled and tapped. See Race Parts more information and to order - Click here
BREATHER HOLDER EXTENSION (1/25/09) Our new Breather Hose Extension allows you to easily relocate the breather hose. Just slip the extension in the valve cover and then slide your own hose into the extension. The 90 degree bend will allows the hose to be rotated out of the way of exhaust or air filters. See Race Parts more information and to order - Click here
22 MM MIKUNI PACKAGES (1/25/09)   Looking for a cheap carb upgrade. See our 22mm Round Slide Mikuni packages. Fro less than $100 you get a complete carb kit that will allow your GX200 to make up to 15 hp. See Race Parts more information and to order - Click here
WELCH PLUG (1/25/09) Planning on modifying your own GX200 or 6.5 carb. If you modify the circuitry you will have to remove the factory welch plug. We now offer a replacement plug to complete the job. Just drive/press back into place. See Race Parts more information and to order - Click here
COPPER HEAD GASKET (1/25/09) Have a zero decked block and need more clearance between the piston and head. Just installed a stroker kit and piston is popping out of the block. Our new copper head gasket might be the solution. At .032" it thicker than the OEM gasket but thinner than the 160 gaskets.  The soft copper also helps sealing heads and blocks that have imperfections on the gasket surface See Race Parts more information and to order - Click here
MOLY RING SET (1/25/09) Tired of buying oversized Honda rings and file fitting. Our new Moly ring has lower tension than the std Honda ring and promotes better sealing. Use with our flat top pistons. Includes both top and 2nd ring See Race Parts more information and to order - Click here
LOW TENSION 2ND RING (1/25/09) Looking to get the last bit of HP out of your engine. Our low tension  2nd Ring are just the ticket. These are OEM 2nd rings that have been "Shrunk" See Race Parts more information and to order - Click here
MODIFIED GUIDE PLATE (1/25/09)  Installing Chrome Moly pushrods? The OEM Guide Plate is too narrow, Our modified guide plates have the slots opened up to work with the larger pushrods. See Race Parts more information and to order - Click here
LOW FRICTION ROCKER ARMS (1/25/09) Does your class require rocker Arms. These match OEM Rocker Arms and Pivots that have been lapped and treated to reduce friction. Undetectable See Race Parts more information and to order - Click here
STROKER CRANKS AND KITS (1/25/09) Check out our new stroker kits. Designed to fit within the stock blocks, these cranks and kits increase the factory stroke by .060 increasing both the cubic inches and compression of the motor. Designed to leave piston .005 in the hole, but due to variation of blocks (and brand of clones), piston may need to be shaved. Alternately, our copper head gasket can be used. See Race Parts more information and to order - Click here
BRONZE VALVE GUIDES (1/25/09) Rebuilding your head, see of Bronze racing valve guides. Honing and/or reaming required to installed. See Race Parts more information and to order - Click here
VALVE PACKAGES (1/15/09) Our Stainless Valve packages take the guess work of picking the right components. Additionally the package price saves over buying each part individually. Each kit comes with valves, retainers, keepers, and springs. Where required lash caps and/or valve seats are included. We have kits in both standard sizes for any power level. See Race Parts more information and to order - Click here
VALVE TRAIN PACKS (1/15/09)   Like our Valve Package, our new Valve Train packages put all the right parts together for you. They contain all the parts in the above package, but add rocker arms, guide plate, and push rods. See Race Parts more information and to order - Click here
CLONES (1/15/09)   We now offer both stock and built clone motors. See Clone Page for more information and to order - Click here
BOX STOCK PROJECT & AKRA MOTORS (1/15/09)   Racing AKRA or Box Stock Project Classes? Want the fastest legal motors available? See our engine packages. Click here
THROTTLE WHEEL & LINKAGES (1/15/09)   Broken throttle on your Carb, See our new throttle wheel which with both repair your carb and provide an excellent linkage system. Also see our new linkages with built in throttle plates. See Engine Accessories more information and to order - Click here